Box Of Synths manualReference
Every effect
What each of the fifteen effects does to the sound, its controls with range and default, and the order the sound passes through them.
This page describes each effect by what you hear and lists its controls. The effects are in the order of the add menu. To add, move, switch off and remove effects, see Effects. For the ranges of every dial in one place, see Every parameter.
Every effect starts off. A new tile switches its effect on. The dial on the tile is marked tile dial. Double-click a tile to open a panel with every control, except for Drive and Analogue, which only have the tile dial.
The fifteen effects here are the built-in ones. A further family of effects from sOURnd, our sister brand, can be added from the last line of the add menu: see sOURnd effects.
The order the sound passes through
The sound goes through these steps, one after the other.
- The voices. The oscillators, the sub, the noise and the filters. Drive works here, inside the filter.
- Analogue, if it is on. It sits at the start of the signal path and does not move.
- Eleven effects, in the order of their tiles. These are Octaver, Fuzz, Pre-amp, Bit crush, Formant, Compressor, Flange, Phaser, Reverb, OTT and Fold. The tiles run left to right, then down, and the sound goes through them in that order. Drag the tiles to change it. An effect that has no tile does not run.
- Chorus, then Delay. These two always run after the eleven. They keep that order unless you put the Delay tile before the Chorus tile, which makes the delay run first.
The Blend slider mixes the whole result with the plain synth: at 0 you hear only the plain synth, at 1 you hear everything. It starts at 1.
An effect that is off, or whose main amount is zero, is skipped and costs no processing.
Fuzz
A hard, fuzzy bass distortion. The more you turn it up, the harder the sound is clipped.
| Control | Range | Default |
|---|---|---|
| Amount (tile dial) | 0 to 3 | 1 |
| Bite | -1 to +1 | 0 |
| Low | -1 to +1 | 0 |
| Body | 0 to 4 | 0 |
| Fuzz level | -12 to +12 dB | 0 dB |
Bite pushes the highs before the clipping, and a negative number softens it. Low blends clean low end back in when positive and trims the deep lows when negative. Body adds weight to the low mids. Fuzz level sets how loud the result is.
Drive
Pushes the sound harder into the filter, for a thicker, harder tone.
| Control | Range | Default |
|---|---|---|
| Drive (tile dial) | 0 to 1 | 0 (a new tile starts at 0.4) |
It is the same control as Drive in the filter section of the engine, and it has no panel.
Octaver
Adds a copy of the sound an octave below or above, blended in with the sound you play.
| Control | Range | Default |
|---|---|---|
| Octave, mix (tile dial) | -1 to +1 | 0 |
| Octave, direction | Down, Up | Down |
Turn the dial left of centre for an octave down, and right of centre for an octave up. The middle is dry. The value reads DRY, DOWN with a percentage, or UP with a percentage. Moving the dial across the middle changes the direction as well.
Flange
A short, swept delay fed back on itself. It sounds like a jet passing over.
| Control | Range | Default |
|---|---|---|
| Amount (tile dial) | 0 to 1 | 0.5 |
| Rate | 0.05 to 5 Hz | 0.3 Hz |
Amount sets the depth, the feedback and the mix together. Rate is how fast the sweep moves.
Phaser
A slow, swirling sweep that moves through the sound. It is the classic phaser sound.
| Control | Range | Default |
|---|---|---|
| Amount (tile dial) | 0 to 1 | 0.5 |
| Rate | 0.05 to 5 Hz | 0.5 Hz |
Pre-amp
The colour of a vintage pre-amp channel, with a three-band tone control, warmth and drive. It is a separate effect from Analogue.
| Control | Range | Default |
|---|---|---|
| Channel | 1 to 20 | 1 |
| Colour (tile dial) | 0 to 200% | 100% |
| Warmth | 0 to 100 | 0 |
| Lo | -16 to +16 dB | 0 dB |
| Mid | -16 to +16 dB | 0 dB |
| Mid Hz | 350, 700, 1.6K, 3.2K, 4.8K, 7.2K | 1.6K |
| Hi | -16 to +16 dB | 0 dB |
| Drive | 0 to 100% | 0 |
Channel picks one of twenty characters. Colour is how much of that character you hear. Lo, Mid and Hi raise or lower three bands, and Mid Hz sets where the middle band sits.
Bit crush
Fewer bits and fewer samples, for a lo-fi, gritty sound.
| Control | Range | Default |
|---|---|---|
| Bits (tile dial) | 2 to 16 | 8 |
| Rate | 1 to 40 x | 4 x |
Fewer Bits sound rougher. A higher Rate holds each sample for longer, which sounds coarser.
Formant
Puts the sound through vowel shapes, like a mouth shaping a voice. You choose two vowels and slide between them. It is the same effect as the Formant block, with the same on switch.
| Control | Range | Default |
|---|---|---|
| Vowel 1 | A, E, I, O, U, Ä, Ö, Ü, Å, OO, UH | A |
| Vowel 2 | The same eleven | O |
| Morph (tile dial) | 0 to 1 | 0 |
| Mix | 0 to 1 | 1 |
| Res | 0 to 1 | 0.6 |
| Shift | -12 to +12 st | 0 |
A higher Res makes the vowel peaks sharper. Shift moves them up or down, like a smaller or bigger throat. The loudness stays steady as you move it.
Compressor
Glues the sound together by turning down the loud parts. Higher settings squash harder, and the makeup gain is automatic.
| Control | Range | Default |
|---|---|---|
| Amount (tile dial) | 0 to 1 | 0.3 |
| Attack | 0.1 to 200 ms | 5 ms |
| Release | 5 to 2000 ms | 120 ms |
One dial does most of the work, because Amount sets how hard it works. The panel's picture shows the curve and a live bar that drops while the sound is being turned down.
Chorus
Width and shimmer, from a slowly moving copy of the sound.
| Control | Range | Default |
|---|---|---|
| Rate | 0.05 to 8 Hz | 0.8 Hz |
| Depth | 0.2 to 12 ms | 3 ms |
| Mix (tile dial) | 0 to 1 | 0.4 |
Delay
Echoes that repeat and fade, with feedback.
| Control | Range | Default |
|---|---|---|
| Time | 10 to 2000 ms | 380 ms |
| Feedback | 0 to 0.95 | 0.35 |
| Mix (tile dial) | 0 to 1 | 0.2 |
| Sync | Free, 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/4d, 1/8d, 1/16d, 1/4t, 1/8t, 1/16t | Free |
Time is the gap between echoes when Sync is Free. Pick a note value in Sync to lock the echoes to the tempo of the host. A d is a dotted note and a t is a triplet. If the note is longer than two seconds, the time is halved until it fits.
Reverb
A small room or hall around the sound.
| Control | Range | Default |
|---|---|---|
| Mix (tile dial) | 0 to 1 | 0.3 |
| Size | 0 to 1 | 0.5 |
| Damp | 0 to 1 | 0.5 |
A bigger Size is a bigger room. A higher Damp makes the highs die away faster.
Analogue
A vintage pre-amp voice that the whole sound goes through, with sparkle that rises with the amount. It sits at the start of the signal path, and it has one dial and no panel.
| Control | Range | Default |
|---|---|---|
| Analogue (tile dial) | 0 to 6 | 0 (off) |
Turn the dial and you walk through six voices, from the gentlest to the most intense: Big 02, Bright 02, Bright 01, Big 01, Outlier 02 and Outlier 01. The whole number picks the voice. The part after the point is how much of it you hear. The value reads like Big 02 35%. Right-click the dial for a list of all twenty voices. A new Analogue tile starts on Big 02 at 35%.
OTT
Pulls both the loud and the quiet parts of three frequency bands toward the middle. At full depth the sound is dense and very bright.
| Control | Range | Default |
|---|---|---|
| Depth (tile dial) | 0 to 1 | 0.5 |
| Time | 0 to 1 | 0.5 |
At a depth of 0 the sound is untouched. Time is in the panel. It sets how fast the squashing reacts and lets go: lower is quicker, higher is slower.
Fold
A wavefolder. Instead of clipping, the sound folds back on itself, which adds a metallic layer. The loudness stays level while the tone changes.
| Control | Range | Default |
|---|---|---|
| Amount (tile dial) | 0 to 1 | 0.4 |
| Shape | 0 to 1 | 0 |
At an Amount of 0 the sound is untouched. Shape leans from a smooth fold at 0 to a sharper, triangular fold at 1.